eprintid: 51238 rev_number: 26 eprint_status: archive userid: 16772 dir: disk0/00/05/12/38 datestamp: 2025-07-11 02:53:21 lastmod: 2025-07-11 02:53:21 status_changed: 2025-07-11 02:53:21 type: thesis metadata_visibility: show contact_email: 3331210064@untirta.ac.id creators_name: Athallah, Rizky Febrian creators_id: 3331210064 contributors_type: http://www.loc.gov/loc.terms/relators/THS contributors_type: http://www.loc.gov/loc.terms/relators/THS contributors_name: Sunardi, Sunardi contributors_name: Jannah, Miftahul contributors_id: 197312052006041002 contributors_id: 199103052020122017 corp_creators: UNIVERSITAS SULTAN AGENG TIRTAYASA corp_creators: FAKULTAS TEKNIK corp_creators: JURUSAN TEKNIK MESIN title: ANALISA FRAKSI VOLUME RASIO CANGKANG TELUR DAN BAMBU SEBAGAI FILLER KOMPOSIT KAMPAS REM YANG MENGALAMI PERENDAMAN AIR LAUT ispublished: pub subjects: TJ subjects: TS divisions: Mesin full_text_status: restricted keywords: composite, eggshell, bamboo fiber, physical-mechanical properties note: Penelitian ini bertujuan untuk menganalisis pengaruh variasi fraksi volume serat bambu dan cangkang telur terhadap sifat fisik dan mekanik komposit kampas rem untuk aplikasi di lingkungan korosif. Tiga komposisi diuji yaitu V1 (25% cangkang telur), V2 (12,5% cangkang telur + 12,5% serat bambu), dan V3 (25% serat bambu), dengan matriks resin epoksi 50%, alumina 10%, ZnO 5%, dan grafit 10%. Pengujian fisik (moisture content, daya serap air, pengembangan tebal) dilakukan setelah perendaman air laut selama 24 jam. Berdasarkan pengujian fisik dan peringkat Multi-Response Performance Index (MRPI) komposisi V3 menunjukkan sifat fisik terbaik dengan moisture content 3,95%, daya serap air 8,22%, dan pengembangan tebal 2,4%, sehingga V3 dipilih untuk pengujian mekanik (kekuatan lentur sesuai dan kekerasan Shore D) setelah perendaman air laut selama 7, 14, dan 21 hari. Hasil menunjukkan V3 memiliki kekuatan lentur 13,15 MPa dan kekerasan 55,33 Shore D setelah 21 hari. Hasil tersebut menunjukkan ketahanan optimal terhadap lingkungan korosif dan memenuhi kebutuhan kampas rem di lingkungan korosif dengan sifat fisik dan mekanik yang unggul. abstract: This study analyzes the effect of volume fraction variations of bamboo fiber and eggshell on the physical and mechanical properties of brake pad composites for applications in corrosive environments. Three compositions were tested: V1 (25% eggshell), V2 (12.5% eggshell + 12.5% bamboo fiber), and V3 (25% bamboo fiber), with a matrix of 50% epoxy resin, 10% alumina, 5% ZnO, and 10% graphite. Physical tests (moisture content, water absorption, and thickness swelling) were conducted after 24 hours of seawater immersion. Based on the physical tests and Multi-Response Performance Index (MRPI) ranking, V3 exhibited the best physical properties with a moisture content of 3.95%, water absorption of 8.22%, and thickness swelling of 2.4%. Consequently, V3 was selected for mechanical testing (flexural strength and Shore D hardness) after seawater immersion for 7, 14, and 21 days. The results showed that V3 achieved a flexural strength of 13.15 MPa and a hardness of 55.33 Shore D after 21 days. These findings demonstrate optimal resistance to corrosive environments, fulfilling the requirements for brake pads in corrosive conditions with superior physical and mechanical properties. date: 2025-07-11 date_type: published pages: 74 institution: Fakultas Teknik Universitas Sultan Ageng Tirtayasa department: TEKNIK MESIN thesis_type: sarjana thesis_name: sarjana referencetext: [1] K. Chaowanna, S. Wisadsatorn and P. Chaowana, "Bamboo As A Sustainable Building Material—Culm Characteristics And Properties," Sustainability, vol. 13, no. 13, p. 7376, 2021. [2] J. O. Agunsoye, S. A. Bello, L. S. Talabi, A. A. Yekinni, I. A. Raheem, A. D. Oderinde and T. E. Idegbekwu, "Recycled Aluminium Cans/Eggshell Composites: Evaluation Of Mechanical And Wear Resistance Properties," Tribology in Industry, vol. 37, no. 1, pp. 107-116, 2015. [3] S. H. Susanto, R. Lusiani, I. Saefuloh, H. A. Notonegoro and M. F. , "Pengaruh Perendaman Bambu Dengan Air Laut Terhadap Kekerasan Dan Laju Keausan Komposit Kampas Rem," Jurnal TURBO, vol. 12, no. 1, pp. 80-87, 2023. [4] M. F. S. and H. Susanto, "Pengaruh Proses Perendaman Bambu Pada Media Lumpur Sebagai Bahan Komposit Dengan Matriks Resin Epoksi Sebagai Bahan Baku Alternatif Kampas Rem," Prosiding Seminar Nasional Industrial Services (SNIS) III, pp. 455-460, 2013. [5] B. A. Ampangallo, "Studi Perilaku Balok Beton Dengan Tulangan Bambu Laminasi Limbah Plastik," Journal on Education, vol. 4, no. 4, pp. 1639-1649, 2022. [6] S. Supriadi, H. Susilo, M. Mulia, S. Gunawan and N. Saputra, "Analisa Pemanfaatan Serat Sabut Kelapa Dan Serat Bambu Pada Pembuatan Kampas Rem Komposit Dengan Uji Mekanis," RODA: Jurnal Pendidikan dan Teknologi Otomotif, vol. 2, no. 1, pp. 49-60, 2022. [7] R. Raliannoor and D. Rahmalina, "Pengaruh Fraksi Volume Penguat 2, 2, 5 Dan 3% Serat Bambu Haur Dan Fiberglass Terhadap Kekuatan Tarik Matriks Poliester," INFO-TEKNIK, vol. 20, no. 2, pp. 141-154, 2020. [8] F. Wang, S. Zhou, M. Yang, Z. Chen and S. Ran, "Thermo-Mechanical Performance Of Polylactide Composites Reinforced With Alkali-Treated Bamboo Fibers," Polymers, vol. 10, no. 4, p. 401, 2018. [9] R. Edokpia, A. V.S and J. O. Agunsoye, "Experimental Study Of The Properties Of Brake Pad Using Egg Shell Particles–Gum Arabic Composites," Journal of the Chinese Advanced Materials Society, vol. 4, no. 2, pp. 172 - 184, 2016. [10] P. Toro, R. Quijada, M. Y. Pedram and J. L. Arias, "Eggshell, A New Bio-Filler For Polypropylene Composites," Materials letters, vol. 61, no. 22, pp. 4347-4350, 2007. [11] R. A. Mensah and et al, "The Eggshell Membrane: A Potential Biomaterial For Corneal Wound Healing," Journal of biomaterials applications, vol. 36, no. 5, pp. 912-929, 2021. [12] M. Matasina, K. Boimau and J. U. Jasron, "Pengaruh Perendaman Terhadap Sifat Mekanik Komposit Polyester Berpenguat Serat Buah Lontar," LONTAR Jurnal Teknik Mesin Undana, vol. 1, no. 2, pp. 47-58, 2014. [13] T. Haramina, N. Hadzic and Z. Keran, "Epoxy Resin Biocomposites Reinforced With Flax And Hemp Fibers For Marine Applications," Journal of marine science and engineering, vol. 11, no. 2, p. 382, 2023. [14] J. Nan, C. Zhi, J. Meng, M. Miao and L. Yu, "Seawater Aging Effect On Fiber-Reinforced Polymer Composites: Mechanical Properties, Aging Mechanism, And Life Prediction," Textile Research Journal, vol. 93, no. 13-14, pp. 3393-3413, 2023. [15] S. Sugiyarto, S. Somawardi, S. Sukanto, Y. Yulianto and M. Asep, "Efek Tekanan Kompaksi Dan Suhu Sintering Terhadap Densitas Dan Kekerasan Komposit Matrik Aluminium Diperkuat Silika Tailing," Turbo, vol. 12, no. 2, pp. 297-305, 2023. [16] C. Pramono, W. Widayat and A. Suprihanto, "Karakteristik Bahan Alternatif Kampas Rem Dari Komposit Berpenguat Serbuk Kayu Jati, Serbuk Tempurung Kelapa, Dan Serbuk Kuningan Dengan Variasi Suhu Post Curing," Jurnal Profesi Insinyur Indonesia, vol. 1, no. 7, pp. 235-241, 2024. [17] A. Borawski, "Conventional And Unconventional Materials Used In The Production Of Brake Pads–Review," Science and Engineering of Composite Materials, vol. 27, no. 1, pp. 374 - 396, 2020. [18] Adui, "Adui Brake," Producing And Customizing Brake Pads, 1997. [Online]. Available: https://www.aduibrake.com/support/brake-pad-material-introduction/non-asbestos-organic-brake-pads. [Accessed 22 November 2024]. [19] A. P. Irawan, D. F. Fitriyana, C. Tezara, J. P. Siregar, D. Laksmidewi, G. D. Baskara, M. Z. Abdullah, R. Junid, A. E. Hadi, M. H. M. Hamdan and N. Najid, "Overview Of The Important Factors Influencing The Performance Of Eco-Friendly Brake Pads," Polymers, vol. 14, no. 6, p. 1180, 2022. [20] G. S. Darius, M. N. Berhan, N. V. David, A. A. Shahrul and M. B. Zaki, "Characterization Of Brake Pad Friction Materials," WIT Transactions on Engineering Sciences, vol. 51, pp. 43 - 50, 2005. [21] R. F. Gibson, Principles Of Composite Material Mechanics, Boca Raton: CRC press, 2007. [22] H. R. Rao, K. M. Reddy, P. V. Reddy and R. M. Reddy, "Effect Of Fibre Orientation On Mechanical Properties Of Hardwika Binata And Bamboo Fibre Reinforced Epoxy Composites," Materials Today: Proceedings, vol. 21, no. 2, pp. 1265 - 1269, 2020. [23] S. Sunardi, D. Ariawan, E. Surojo, A. R. Prabowo, H. I. Akbar, A. Sudrajad and H. Seputro, "Optimization Of Eggshell Particles To Produce Eco-Friendly Green Fillers With Bamboo Reinforcement In Organic Friction Materials," Reviews on Advanced Materials Science, vol. 62, no. 1, p. 20230111, 2023. [24] V. Chauhan, J. Bijwe and A. Darpe, "Functionalization Of Alumina Particles To Improve The Performance Of Eco-Friendly Brake-Pads," Friction, vol. 9, pp. 1213 - 1226, 2021. [25] M. Ramesh, L. N. Rajeshkumar, N. Srinivasan, D. V. Kumar and D. Balaji, "Influence Of Filler Material On Properties Of Fiber-Reinforced Polymer Composites: A Review," E-Polymers, vol. 22, no. 1, pp. 898 - 916, 2022. [26] A. Yudhanto and B. K. Hadi, "Buckling Of Isotropic And Composite Cylindrical Shells Under Axial Compression: Can Composite Save Weight?," Journal Of The Indonesian Oil And Gas Community, pp. 1-8, 2006. [27] A. M. King'ori, "A Review Of The Uses Of Poultry Eggshells And Shell Membranes," International Journal of Poultry Science, vol. 10, no. 11, pp. 908-912, 2011. [28] P. Toro, R. Quijada, M. Y. Pedram and J. L. Arias, "Eggshell, A New Bio-Filler For Polypropylene Composites," Materials letters, vol. 61, no. 22, pp. 4347-4350, 2007. [29] P. Zakikhani, R. Zahari, M. T. Sultan and D. L. Majid, "Extraction And Preparation Of Bamboo Fibre-Reinforced Composites," Materials & Design, vol. 63, pp. 820-828, 2014. [30] M. Jawaid and H. P. A. Khalil, "Cellulosic/Synthetic Fibre Reinforced Polymer Hybrid Composites: A Review," Carbohydrate polymers, vol. 86, no. 1, pp. 1-18, 2011. [31] W. D. Kingery, H. K. Bowen and D. R. Uhlmann, Introduction To Ceramics, Canada: John wiley & sons, 1976. [32] J. Bijwe, J. J. Rajesh, A. Jeyakumar, A. Ghosh and U. S. Tewari, "Influence Of Solid Lubricants And Fibre Reinforcement On Wear Behaviour Of Polyethersulphone," Tribology International, vol. 33, no. 10, pp. 697-706, 2000. [33] K. K. Chawla, Composite Materials: Science And Engineering, Birmingham: Springer Science & Business Media, 2012. [34] M. Naresh, G. S. S. Krishna, A. D. Kumar and T. Deepthi, "Optimisation Of Mechanical Properties And Fundamental Parameters Of Green Composite Materials For Brake Pads," International Journal Of Scientific & Technology Research, vol. 9, no. 3, pp. 6075 - 6080, 2020. [35] Y. Yang, L.-x. Liang, H. Wu, B.-w. Liu, H. Qu and Q.-h. Fang, "Effect Of Zinc Powder Content On Tribological Behaviors Of Brake Friction Materials," Transactions of Nonferrous Metals Society of China, vol. 30, no. 11, pp. 3078-3092, 2020. [36] C. Venkatesh, M. Laurenti, M. Bandeira, E. Lanzagorta, L. Lucherini, V. Cauda and D. M. Devine, "Biodegradation And Antimicrobial Properties Of Zinc Oxide–Polymer Composite Materials For Urinary Stent Applications," Coatings, vol. 10, no. 10, p. 1002, 2020. [37] M. Alajmi, K. R. Alrashdan, T. Alsaeed and A. Shalwan, "Tribological Characteristics Of Graphite Epoxy Composites Using Adhesive Wear Experiments," Journal of Materials Research and Technology, vol. 9, no. 6, pp. 13671 - 13681, 2020. [38] S. Sunardi, D. Ariawan, E. Surojo, A. R. Prabowo, H. I. Akbar and C. H. Wibowo, Pengembangan Kampas Rem Organik Non-Asbestos Dan Tantangan Lingkungan, Yogyakarta: K-Media, 2024. [39] K. Vikram, S. Bhaumik and S. Pramanik, "Effect Of Graphite On Tribological And Mechanical Properties Of PA6/5GF Composites," Journal of Thermal Analysis and Calorimetry, vol. 148, no. 9, pp. 3341 - 3355, 2023. [40] K. Kosjoko, "Pengaruh Perendaman (Naoh) Terhadap Kekuatan Tarik Dan Bending Bahan Komposit Serat Bambu Tali (Gigantochloa Apus) Bermatriks Polyester," INFO-TEKNIK, vol. 15, no. 2, pp. 139 - 148, 2014. [41] A. Budiman and S. Sugiman, "Karakteristik Sifat Mekanik Komposit Serat Bambu Resin Polyester Tak Jenuh Dengan Filler Partikel Sekam," Dinamika Teknik Mesin, vol. 6, no. 1, pp. 76 - 82, 2016. [42] Y. Anggreni, S. Sugiyarto, A. Rusdy, I. A. Wahyudie, R. Rodika, Y. Oktriadi and S. Sukanto, "Pembuatan Komposit AMC Hybrid Baggase Ash Dan Alumina Metode Metalurgi Serbuk," Dinamika: Teknik Mesin Unkhair, vol. 8, no. 2, pp. 65 - 74, 2023. [43] M. Ünaldı and R. Kuş, "The Determination Of The Effect Of Mixture Proportions And Production Parameters On Density And Porosity Features Of Miscanthus Reinforced Brake Pads By Taguchi Method," International Journal Of Automotive Engineering And Technologies, vol. 7, no. 1, pp. 48 - 57, 2018. [44] F. R. Hidayat, F. Setiawan and D. Wicaksono, "The Influence Of Stirring Speed On Tensile Strength Of Fiberglass Composite Using VARI Method," Journal Of Metallurgical Engineering And Processing Technology, vol. 4, no. 1, pp. 57 - 65, 2023. [45] A. Ratmanto, W. W. Raharjo and T. Triyono, "Pengaruh Tekanan Pengepresan Terhadap Kekuatan Bending Komposit HDPE Cantula," Prosiding Sains Nasional dan Teknologi, vol. 1, no. 1, pp. 46 - 50, 2016. [46] M. F. Alamsyah and Sulardjaka, "Pengaruh Holding Time Pada Proses Age Hardening Terhadap Kekerasan Komposit AL-CU Yang Diperkiat Serbuk Fly Ash," Jurnal Teknik Mesin, vol. 1, no. 1, pp. 6-12, 2013. [47] C. Campana, R. Leger, R. Sonnier, L. Ferry and P. Ienny, "Effect Of Post Curing Temperature On Mechanical Properties Of A Flax Fiber Reinforced Epoxy Composite," Composites Part A: Applied Science And Manufacturing, vol. 107, pp. 171 - 179, 2018. [48] M. K. Huda, "Analisis Pengaruh Variasi Alkalisasi Pada Serat bambu Terhadap Absorbsi Air Dan Kekuatan Tarik Komposit Recy Cled Polypropylene-Bambu," 2021. [49] M. M. Kabir, H. Wang, K. T. Lau and F. Cardona, "Chemical Treatments On Plant-Based Natural Fibre Reinforced Polymer Composites: An Overview," Composites Part B: Engineering, vol. 43, no. 7, pp. 2883-2892, 2012. [50] L. Xuan, X. Shi, G. Xu and J. Zheng, "Research Note: Three-Dimensional Microstructural Basis For Chicken Eggshell Translucency," Poultry Science, vol. 102, no. 12, p. 103149., 2023. [51] G. Refiadi, Y. S. Syamsiar and H. Judawisastra, "Sifat Komposit Epoksi Berpenguat Serat Bambu Pada Akibat Penyerapan Air," Jurnal Sains Materi Indonesia, vol. 19, no. 3, pp. 98-104, 2018. [52] M. Rokbi, H. Osmani, A. Imad and N. Benseddiq, "Effect Of Chemical Treatment On Flexure Properties Of Natural Fiber-Reinforced Polyester Composite," Procedia Engineering, vol. 10, pp. 2092-2097, 2011. [53] P. K. Kushwaha and R. Kumar, "Studies On Water Absorption Of Bamboo‐Epoxy Composites: Effect Of Silane Treatment Of Mercerized Bamboo," Journal Of Applied Polymer Science, vol. 115, no. 3, pp. 1846-1852, 2010. [54] J. Antony, "Simultaneous Optimisation Of Multiple Quality Characteristics In Manufacturing Processes Using Taguchi's Quality Loss Function," The International Journal of Advanced Manufacturing Technology, vol. 17, pp. 134-138, 2001. [55] T. Evangelos, Multi-Criteria Decision Making Methods, Springer Us, 2000. [56] O. P. Prastuti, "Pengaruh Komposisi Air Laut Dan Pasir Laut Sebagai Sumber Energi Listrik," Jurnal Teknik Kimia dan Lingkungan, vol. 1, no. 1, pp. 35-41, 2017. [57] P. Manik, A. Suprihanto, S. Sulardjaka and S. Nugroho, "Analysis Of Salinity From Seawater On Physical And Mechanical Properties Of Laminated Bamboo Fiber Composites With An Epoxy Resin Matrix For Ship Skin Materials," Int Rev Mech Eng, vol. 15, no. 7, pp. 365-77, 2021. [58] Y.-N. Zhao, S. Tian, Y.-M. Chen, Y.-T. Yan, S.-Y. Jin, X. Zhang and G.-B. Li, "The Influence Of Mineral Salt Interface Modifier To Pavement Rubber Concrete Strength," International Conference On Material Science And Applications (icmsa-15), pp. 271-275, 2015. [59] D. J. Y. S. Page and T. G. Gopakumar, "Properties And Crystallization Of Maleated Polypropylene/Graphite Flake Nanocomposites," Polymer Journal, vol. 38, no. 9, pp. 920-929, 2006. [60] L. Yan and N. Chouw, "Effect Of Water, Seawater And Alkaline Solution Ageing On Mechanical Properties Of Flax Fabric/Epoxy Composites Used For Civil Engineering Applications," Construction And Building Materials, vol. 99, pp. 118-127, 2015. [61] P. E. Chatzistergos, D. Allan, N. Chockalingam and R. Naemi, "Shore Hardness Is A More Representative Measurement Of Bulk Tissue Biomechanics Than Of Skin Biomechanics," Medical Engineering and Physics, vol. 105, p. 103816, 2022. citation: Athallah, Rizky Febrian (2025) ANALISA FRAKSI VOLUME RASIO CANGKANG TELUR DAN BAMBU SEBAGAI FILLER KOMPOSIT KAMPAS REM YANG MENGALAMI PERENDAMAN AIR LAUT. S1 thesis, Fakultas Teknik Universitas Sultan Ageng Tirtayasa. document_url: https://eprints.untirta.ac.id/51238/1/Rizky%20Febrian%20Athallah_3331210064_Fulltext..pdf document_url: https://eprints.untirta.ac.id/51238/2/Rizky%20Febrian%20Athallah_3331210064_01..pdf document_url: https://eprints.untirta.ac.id/51238/3/Rizky%20Febrian%20Athallah_3331210064_02..pdf document_url: https://eprints.untirta.ac.id/51238/4/Rizky%20Febrian%20Athallah_3331210064_03..pdf document_url: https://eprints.untirta.ac.id/51238/5/Rizky%20Febrian%20Athallah_3331210064_04..pdf document_url: https://eprints.untirta.ac.id/51238/6/Rizky%20Febrian%20Athallah_3331210064_05..pdf document_url: https://eprints.untirta.ac.id/51238/7/Rizky%20Febrian%20Athallah_3331210064_Ref..pdf document_url: https://eprints.untirta.ac.id/51238/8/Rizky%20Febrian%20Athallah_3331210064_Lamp..pdf document_url: https://eprints.untirta.ac.id/51238/9/Rizky%20Febrian%20Athallah_3331210064_CP..pdf