eprintid: 47968 rev_number: 19 eprint_status: archive userid: 7894 dir: disk0/00/04/79/68 datestamp: 2025-03-20 02:03:24 lastmod: 2025-03-20 02:03:24 status_changed: 2025-03-20 02:03:24 type: thesis metadata_visibility: show contact_email: 3334200102@untirta.ac.id creators_name: NURCHOLIFAAH, NURCHOLIFAAH creators_id: 3334200102 contributors_type: http://www.loc.gov/loc.terms/relators/THS contributors_type: http://www.loc.gov/loc.terms/relators/THS contributors_name: DIDIED, HARYONO contributors_name: BENING NURUL, HIDAYAH KAMBUNA contributors_id: 196705302002121001 contributors_id: 199008292020122013 corp_creators: UNIVERSITAS SULTAN AGENG TIRTAYASA corp_creators: FAKULTAS TEKNIK corp_creators: TEKNIK METALURGI title: MONITORING FLOTASI KOLOM MENGGUNAKAN SINYAL KAPASITANSI PADA PENGARUH pH DAN DOSIS FROTHER ispublished: pub subjects: TN divisions: Metalurgi full_text_status: restricted keywords: Recovery, Kadar, Flotasi Kolom, Sensor Kapasitif, Sinyal Kapasitansi. abstract: Flotasi adalah metode pemisahan mineral berharga dari pengotornya yang didasarkan pada perbedaan sifat permukaan partikel, yaitu hidrofobik dan hidrofilik. Efektivitas proses flotasi kolom biasanya dievaluasi melalui pengukuran recovery dan kadar, yang menjadi indikator penting dalam meningkatkan efisiensi proses. Saat ini, monitoring proses flotasi kolom di industri umumnya dilakukan menggunakan teknologi machine vision, yaitu suatu metode monitoring dengan cara memotret permukaan (froth zone) ketika proses flotasi berlangsung. Pendekatan ini memiliki keterbatasan karena proses pemisahan berlangsung di collection zone. Untuk mengatasi kendala tersebut, telah dikembangkan monitoring menggunakan teknik tomografi yang berbasis kapasitansi listrik. Sensor kapasitif dipasang di luar dinding kolom pada collection zone untuk memonitor kinerja flotasi kolom (sumbu-z). Penelitian ini bertujuan menguji kemampuan sensor kapasitif dalam me-monitor proses flotasi kolom menggunakan besaran recovery. Pengujian dilakukan pada skala laboratorium dengan menggunakan bijih pirit. Variabel yang diuji meliputi variasi nilai pH 7, 8, 10, dan 12 serta variasi dosis frother 2, 3, 4, dan 5 tetes. Pengukuran kapasitansi dilakukan pada tengah kolom flotasi, yang merupakan daerah steady state. Hasil penelitian menunjukkan bahwa semakin tinggi nilai pH yang digunakan, maka akan semakin tinggi persen recovery yang dihasilkan. Persen recovery tertinggi didapat pada pH 12 sebesar 35,80%. Kemudian, semakin tinggi dosis frother yang digunakan, persen recovery yang dihasilkan juga akan semakin tinggi hingga mencapai nilai optimumnya. Nilai optimum pada dosis 4 tetes, yaitu 42,09%. Secara umum sinyal kapasitansi terbukti mampu menunjukkan hubungan yang konsisten dengan performa metalurgi dalam proses flotasi kolom. Variasi Nilai pH dalam rentang 7 – 12 menurunkan nilai kapasitansi terukur dari 10,32 pF menjadi 3,57 pF, sedangkan variasi dosis frother dalam rentang 2 – 5 tetes meningkatkan nilai kapasitansi terukur dari 9,03 pF menjadi 10,37 pF. Hal ini menunjukkan bahwa sinyal kapasitansi dapat mengindikasikan penambahan nilai recovery dan kadar dalam proses flotasi kolom. Dengan demikian, penggunaan sinyal kapasitansi dapat menjadi alat yang efektif untuk memonitor dan mengevaluasi kinerja flotasi kolom secara real-time. date: 2025-03-20 date_type: published pages: 203 institution: Fakultas Teknik Universitas Sultan Ageng Tirtayasa department: TEKNIK METALURGI thesis_type: sarjana thesis_name: sarjana referencetext: [1] S. Aghazadeh, S. K. Mousavinezhad, and M. Gharabaghi, “Chemical and colloidal aspects of collectorless flotation behavior of sulfide and non-sulfide minerals,” Adv. Colloid Interface Sci., vol. 225, pp. 203–217, 2015, doi: 10.1016/j.cis.2015.09.007. [2] I. Alp, H. Deveci, E. Y. Yazici, T. Türk, and Y. H. Süngün, “Potential use of pyrite cinders as raw material in cement production: Results of industrial scale trial operations,” J. Hazard. Mater., vol. 166, no. 1, pp. 144–149, 2009, doi: 10.1016/j.jhazmat.2008.10.129. [3] D. Haryono, S. Harjanto, H. Nugraha, M. Al Huda, and W. P. Taruno, “Column flotation monitoring based on electrical capacitance volume tomography: A preliminary study,” AIP Conf. Proc., vol. 1805, 2017, doi: 10.1063/1.4974436. [4] D. Haryono, S. Harjanto, H. F. Rahmandani, S. Oediyani, H. Nugraha, and M. A. Huda, “A Preliminary study of three-phase column flotation process monitoring using electrical capacitance volume tomography,” IOP Conf. Ser. Mater. Sci. Eng., vol. 673, no. 1, 2019, doi: 10.1088/1757-899X/673/1/012130. [5] S. Oediyani, D. Haryono, M. Elisabeth, and R. F. Suwandana, “The monitoring process of column flotation using ECVT system with the effect of percent solid and frother dosage to recovery,” Tek. J. Sains dan Teknol., vol. 19, no. 1, p. 1, 2023, doi: 10.36055/tjst.v18i2.16693. [6] M. Zulfitrah, L. Lantu, and S. Syamsuddin, “Identifikasi Sebaran Mineral Sulfida (Pirit) Menggunakan Metode Geomagnet Di Daerah Libureng Kabupaten Bone,” J. Geocelebes, vol. 2, no. 1, p. 36, 2018, doi: 10.20956/geocelebes.v2i1.3789. [7] A. Haris, B. D. Amin, A. M. Yusuf, and N. Nurhasmi, “Sintesis dan Karakterisasi Pyrite (FeS2) Dari DEposit Mineral Kecamatan Bontocani, Kabupatem Bone, Sulawesi Selatan,” J. Sains dan Pendidik. Fis., vol. 10, no. 3, pp. 263–268, 2014. [8] A. A. Neisiani and S. C. Chelgani, “Asam yang dapat terurai secara hayati untuk depresi pirit dan pemisahan flotasi hijau - sebuah tinjauan umum,” 2023. [9] T. Alfredo, “Pembuatan Prototipe Alat Pencucian Batubara Dengan Metode Flotasi,” J. Bina Tambang, vol. 6, no. 2, pp. 265–275, 2020. [10] M. Andrian, “Monitoring Proses Flotasi Kolom Bijih Sphalerite Menggunakan ECVT dengan Variasi Laju Alir Udara, Dosis Frother Oreprep F-583-OZ, dan pH terhadap Recovery,” Fak. Tek. Univ. Sultan Ageng Tirtayasa, 2019 [11] B. A. Wills and J. A. Finch, Wills’ mineral processing technology: An introduction to the practical aspects of ore treatment and mineral recovery. Elsevier, 2015. [12] G. Saputra, “Monitoring Flotasi Kolom dengan Sinyal Kapasitansi : Investigasi Pengaruh Dosis Frother dan Laju Alir Udara terhadap Recovery,” Fak. Tek. Univ. Sultan Ageng Tirtayasa, 2017. [13] Y. Rubinstein, “Column flotation: Theory and practice,” IMPC 2018 - 29th Int. Miner. Process. Congr., pp. 1920–1931, 2019. [14] D. Haryono, I. Darmabakti, S. Oediyani, and S. Harjanto, “Monitoring of Column Flotation Process in Collection Zone using ECVT with the Effect of Collector and Frother Doses to Recovery,” Mesin, vol. 11, no. 1, pp. 1–7, 2020, doi: 10.25105/ms.v11i1.7442. [15] J. B. Yianatos, “Column Flotation Modelling and Technology,” Chemical Engineering Departement, University of Santa Maria, Valparaiso, 110-V, Chile, 2015. [16] C. Bazin and M. Proulx, “Distribution of reagents down a flotation bank to improve the recovery of coarse particles,” Int. J. Miner. Process., vol. 61, no. 1, pp. 1–12, 2001, doi: 10.1016/S0301-7516(00)00022-3. [17] G. I. Sabil, “Monitoring Proses Flotasi Kolom Bijih Sphalerite Menggunakan ECVT dengan Variasi Laju Alir Udara, Dosis Frother MIBC dan Dosis Kolektor PAX Terhadap Recovery,” Fak. Tek. Univ. Sultan Ageng Tirtayasa, 2019. [18] R. Desiasni, A. Kusmiran, P. Studi Teknik Metalurgi, and U. Teknologi Sumbawa, “Analisis Pengaruh Variasi Dosis Reagent Modifier MODIFIER RA666 Terhadap % Recovery Cu, Au dan CuASN,” J. Tambora, vol. 3, no. 2, pp. 107–113, 2019, [Online]. Available: http://jurnal.uts.ac.id [19] H. L. De Moura, D. R. Pipa, A. D. N. Wrasse, and M. J. Da Silva, “Image Reconstruction for Electrical Capacitance Tomography Through Redundant Sensitivity Matrix,” IEEE Sens. J., vol. 17, no. 24, pp. 8157–8165, 2017, doi: 10.1109/JSEN.2017.2719003. [20] W. Kartika, I. Susanto, and S. Permana, “Optimalisasi variabel flotasi nikel laterit,” Fak. Tek. Univ. Indonesia, 2011 . [21] M. R. Dono Guntoro, Sri Widayati, “Kajian Mengenai Peningkatan Kadar Fe Total pada Bijih Besi Laterit Menggunakan Magnetic Separator di PT Aikona Bima Amarta Kecamatan Bajuin , Kabupaten Tanah Laut Provinsi Kalimantan Selatan,” Pros. Tek. Pertamb. Prodi Pertambangan, Fak. Tek. Univ. Islam Bandung, vol. 10, pp. 544–551, 2017. [22] S. L. Dahake, R. N. Dhar, A. K. Saxena, V. K. Batra, and K. Chandra, “Progress in the Realization of the Units of Capacitance, Resistance, and Inductance at the National Physical Laboratory, India,” IEEE Trans. Instrum. Meas., vol. 32, no. 1, pp. 5–8, 1983, doi: 10.1109/TIM.1983.4314999. [23] S. Westerlund, “Capacitor Theory,” IEEE Trans. Dielectr. Electr. Insul., vol. 1, no. 5, pp. 1–3, 1994. [24] S. M. Siagian, G. W. Jaya, and I. Nurhidayati, “Analisis Jumlah Muatan Listrik Serta Energi Pada Kapasitor Berdasarkan Konstanta Dielektrik Suatu Material,” ORBITA J. Kajian, Inov. dan Apl. Pendidik. Fis., vol. 7, no. 1, p. 176, 2021, doi: 10.31764/orbita.v7i1.4420. [25] J. Qin et al., “Flexible and Stretchable Capacitive Sensors with Different Microstructures,” Adv. Mater., vol. 33, no. 34, pp. 1–31, 2021, doi: 10.1002/adma.202008267. [26] Y. Luo et al., “Flexible Capacitive Pressure Sensor Enhanced by Tilted Micropillar Arrays,” ACS Appl. Mater. Interfaces, vol. 11, no. 19, pp. 17796–17803, 2019, doi: 10.1021/acsami.9b03718. [27] M. A. Hendrawan, J. Pitulima, and Guskarnali, “Identification of mineral characterization and alteration types in primary tin deposits of oxide skarn type in Batubesi mining areas by petrographic analysis and grain counting analysis,” IOP Conf. Ser. Earth Environ. Sci., vol. 1108, no. 1, pp. 0–6, 2022, doi: 10.1088/1755-1315/1108/1/012042. [28] W. Wang and L. Wang, “An image processing method for grains counting,” Commun. Comput. Inf. Sci., vol. 326 CCIS, no. PART 1, pp. 181–185, 2012, doi: 10.1007/978-3-642-34381-0_21. [29] S. R. Gallagher, “Digital image processing and analysis with imagej,” Curr. Protoc. Essent. Lab. Tech., vol. 2014, no. November, p. A.3C.1-A.3C.29, 2014, doi: 10.1002/9780470089941.eta03cs9. [30] A. B. Schroeder, E. T. A. Dobson, C. T. Rueden, P. Tomancak, F. Jug, and K. W. Eliceiri, “The ImageJ ecosystem: Open-source software for image visualization, processing, and analysis,” Protein Sci., vol. 30, no. 1, pp. 234–249, 2021, doi: 10.1002/pro.3993. [31] E. Vandel, T. Vaasma, and S. Sugita, “Application of image analysis technique for measurement of sand grains in sediments,” MethodsX, vol. 7, p. 100981, 2020, doi: 10.1016/j.mex.2020.100981. [32] C. T. Rueden et al., “ImageJ2: ImageJ for the next generation of scientific image data,” BMC Bioinformatics, vol. 18, no. 1, pp. 1–26, 2017, doi: 10.1186/s12859-017-1934-z. [33] H. Ren, M. Q. Ren, Z. Li, J. Ning, and Y. F. Zhang, “Sphalerite/silica interaction: Zeta potential distribution measurement,” Rare Met., vol. 35, no. 9, pp. 729–734, 2016, doi: 10.1007/s12598-014-0283-6. [34] Warjito and I. P. Al Kautsar, “Effects of pine oil on dynamics of bubble in froth flotation,” Appl. Mech. Mater., vol. 493, pp. 155–160, 2014, doi: 10.4028/www.scientific.net/AMM.493.155. [35] K. C. Corin and J. G. Wiese, “Investigating froth stability: A comparative study of ionic strength and frother dosage,” Miner. Eng., vol. 66, pp. 130–134, 2014, doi: 10.1016/j.mineng.2014.03.001. [36] F. Melo and J. S. Laskowski, “Fundamental properties of flotation frothers and their effect on flotation,” Miner. Eng., vol. 19, no. 6–8, pp. 766–773, 2006, doi: 10.1016/j.mineng.2005.09.031. [37] M. S. Arefin, M. B. Coskun, T. Alan, A. Neild, J. M. Redoute, and M. R. Yuce, “A MEMS capacitive pH sensor for high acidic and basic solutions,” Proc. IEEE Sensors, vol. 2014-Decem, no. December, pp. 1792–1794, 2014, doi: 10.1109/ICSENS.2014.6985373. [38] ECVT Team, “User Guide for Engineer, Capasitometer Model Cap3201 2CH, High Speed 1000 Frames/s,” Ctech-Labs, Edwar Technology Co, 2015. http://www.c-techlabs.com. citation: NURCHOLIFAAH, NURCHOLIFAAH (2025) MONITORING FLOTASI KOLOM MENGGUNAKAN SINYAL KAPASITANSI PADA PENGARUH pH DAN DOSIS FROTHER. S1 thesis, Fakultas Teknik Universitas Sultan Ageng Tirtayasa. document_url: https://eprints.untirta.ac.id/47968/1/Nurcholifaah_3334200102_Fulltext.pdf document_url: https://eprints.untirta.ac.id/47968/2/Nurcholifaah_3334200102_01.pdf document_url: https://eprints.untirta.ac.id/47968/3/Nurcholifaah_3334200102_02.pdf document_url: https://eprints.untirta.ac.id/47968/4/Nurcholifaah_3334200102_03.pdf document_url: https://eprints.untirta.ac.id/47968/5/Nurcholifaah_3334200102_04.pdf document_url: https://eprints.untirta.ac.id/47968/7/Nurcholifaah_3334200102_05.pdf document_url: https://eprints.untirta.ac.id/47968/8/Nurcholifaah_3334200102_Ref.pdf document_url: https://eprints.untirta.ac.id/47968/9/Nurcholifaah_3334200102_Lamp.pdf document_url: https://eprints.untirta.ac.id/47968/10/Nurcholifaah_3334200102_CP.pdf