relation: https://eprints.untirta.ac.id/46893/
title: PROSES PEMBENTUKAN DAN UJI MEKANIK PRODUK PALU BERBAHAN LIMBAH PLASTIK HASIL INJECTON MOULDING DENGAN VARIASI BAHAN PLASTIK POLYETHYLENE TEREPHTHALATE (PET) DAN ,POLYPROPYLENE (PP)
creator: MAHENDRA, DISA PUTRA
subject: TJ Mechanical engineering and machinery
description: Plastic is a material that has a lower crystallization rate than fibers and can be melted or shaped. The objectives of the study are as follows: To determine the effect of temperature variations on hammer products resulting from the plastic waste treatment process by injection molding in PET plastic and PP plastic variants. Obtain the mechanical test values and physical characteristics between PET plastic and PP plastic. The research method used is experimental. The results were obtained as follows: the max load of pure PP plastic is 455.76 N, the tensile stress is 7.17 MPa, the handle is 12% and the modulus of elasticity is 59.98 MPa. Pure PET has   a max load of 398.26 N, tensile strength of 8.11 MPa, strain of 11.33% and modulus of elasticity of 74.76. PP and PET 200°C get a max load value of 372.16, tensile stress of 12.40 MPa, strain of 9.33% and modulus of elasticity of 122.17 MPa. PP and PET 250°C max load 398.67 N, tensile tensile strength 13.29 MPa, strain 12% and modulus elasticity 61.36MPa.
date: 2025-02-15
type: Thesis
type: NonPeerReviewed
format: text
language: en
identifier: https://eprints.untirta.ac.id/46893/1/Disa%20Putra%20Mahendra_3331210012_02.pdf
format: text
language: en
identifier: https://eprints.untirta.ac.id/46893/2/Disa%20Putra%20Mahendra_3331210012_REF.pdf
format: text
language: en
identifier: https://eprints.untirta.ac.id/46893/3/DISA%20MAHENDRA%20PUTRA_3331210012_CP.pdf
format: text
language: en
identifier: https://eprints.untirta.ac.id/46893/4/DISA%20MAHENDRA%20PUTRA_3331210012_Fulltext.pdf
format: text
language: en
identifier: https://eprints.untirta.ac.id/46893/5/Disa%20Putra%20Mahendra_3331210012_01.pdf
format: text
language: en
identifier: https://eprints.untirta.ac.id/46893/6/Disa%20Putra%20Mahendra_3331210012_03.pdf
format: text
language: en
identifier: https://eprints.untirta.ac.id/46893/7/Disa%20Putra%20Mahendra_3331210012_04.pdf
format: text
language: en
identifier: https://eprints.untirta.ac.id/46893/8/Disa%20Putra%20Mahendra_3331210012_05.pdf
format: text
language: en
identifier: https://eprints.untirta.ac.id/46893/9/Disa%20Putra%20Mahendra_3331210012_LAMP.pdf
identifier:   MAHENDRA, DISA PUTRA  (2025) PROSES PEMBENTUKAN DAN UJI MEKANIK PRODUK PALU BERBAHAN LIMBAH PLASTIK HASIL INJECTON MOULDING DENGAN VARIASI BAHAN PLASTIK POLYETHYLENE TEREPHTHALATE (PET) DAN ,POLYPROPYLENE (PP).  S1 thesis, Fakultas Teknik Universitas Sultan Ageng Tirtayasa.