eprintid: 44128
rev_number: 84
eprint_status: archive
userid: 13859
dir: disk0/00/04/41/28
datestamp: 2024-11-25 11:15:25
lastmod: 2024-11-25 11:15:25
status_changed: 2024-11-25 11:15:25
type: thesis
metadata_visibility: show
creators_name: Fadhil Hilal, Muhammad
creators_id: 3333200091
contributors_type: http://www.loc.gov/loc.terms/relators/THS
contributors_type: http://www.loc.gov/loc.terms/relators/THS
contributors_name: Hary Yadi, Yayan
contributors_name: Sri Mariawati, Ade
contributors_id: 0002097703
contributors_id: 0026037708
corp_creators: universitas Sultan Ageng Tirtayasa
corp_creators: Fakultas Teknik
corp_creators: Jurusan Teknik Industri
title: PENENTUAN PRIORITAS RISIKO PEKERJAAN HOTWORK DENGAN METODE FMEA DAN FTA PADA PEMBANGUNAN PEMBANGKIT LISTRIK TENAGA UAP SURALAYA
ispublished: pub
subjects: TH
divisions: FT
divisions: Industri
full_text_status: restricted
note: K3 sangat penting saat membangun PLTU, terutama untuk aktivitas hotwork berisiko tinggi seperti pengelasan dan penggunaan cutting tourch yang penentuan prioritas risiko kerja hotwork masih tidak sepenuhnya dipahami oleh banyak pekerja. Penelitian ini menggunakan Failure Mode Effect Analysis (FMEA) untuk mendeteksi bahaya pekerjaan hotwork di area Steam Turbin Generator (STG) pada PLTU. Ini juga menggunakan FTA untuk mengetahui sumber masalah dari RPN tertinggi. Pendekatan studi ini terdiri dari observasi, wawancara, distribusi kuesioner kepada karyawan STG, analisis data menggunakan FMEA, prioritas risiko menggunakan diagram Pareto, dan analisis akar penyebab menggunakan FTA. Hasil penelitian, terdapat 14 bahaya hotwork. Risiko ledakan lampu beam memiliki RPN tertinggi yaitu 180, dan risiko ledakan berada di angka 150 dengan kategori rendah. Dengan kumulatif sebesar 24%, diagram Pareto menunjukkan bahwa risiko ledakan lampu beam dan ledakan adalah prioritas tertinggi. Hasil analisis FTA, Faktor penyebab kecelakaan terbagi menjadi dua: unsafe condition meliputi kerusakan komponen (lampu retak, ballast rusak) dan kondisi lingkungan ekstrem (suhu, kelembaban), serta unsafe action mencakup kesalahan manusia seperti pemasangan tidak tepat dan penggunaan alat tidak sesuai spesifikasi.
abstract: Safety and health at work are important aspects in the building of Steam Power Plants (PLTU), especially for high-risk hotwork activities such as welding and the use of cutting torches, where the prioritization of hotwork risk is still not fully understood by many workers. Failure Mode Effect Analysis (FMEA) is used in this investigation.approach to detect hotwork hazards in the Steam Turbine Generator (STG) area at the coal-fired power plant (PLTU). It also employs Fault Tree Analysis (FTA) to determine the underlying cause of the most significant RPN problems. The study approach consists of observation, interviews, distribution of questionnaires to STG employees, data analysis using FMEA, risk prioritization using the Pareto diagram, and root cause analysis using FTA. The research results identified 14 hotwork hazards. The risk of a beam lamp explosion has the highest RPN at 180, and the risk of an explosion is at 150 with a low category. With a cumulative total of 24%, the Pareto diagram shows that the risks of beam lamp explosions and explosions are the highest priorities. FTA analysis results show that the causes of accidents are divided into two categories: unsafe conditions, which include component damage (cracked lamps, faulty ballasts) and extreme environmental conditions (temperature, humidity), and unsafe actions, which include human errors such as improper installation and use of tools not according to specifications.
date: 2024-11-25
date_type: published
pages: 119
institution: Fakultas Teknik Universitas Sultan Ageng Tirtayasa
department: Teknik Industri
thesis_type: sarjana
thesis_name: sarjana
citation:   Fadhil Hilal, Muhammad  (2024) PENENTUAN PRIORITAS RISIKO PEKERJAAN HOTWORK DENGAN METODE FMEA DAN FTA PADA PEMBANGUNAN PEMBANGKIT LISTRIK TENAGA UAP SURALAYA.  S1 thesis, Fakultas Teknik Universitas Sultan Ageng Tirtayasa.   
document_url: https://eprints.untirta.ac.id/44128/14/MUHAMMAD%20FADHIL%20HILAL_3333200091_FULLTEXT.pdf
document_url: https://eprints.untirta.ac.id/44128/13/MUHAMMAD%20FADHIL%20HILAL_3333200091_%2001.pdf
document_url: https://eprints.untirta.ac.id/44128/3/MUHAMMAD%20FADHIL%20HILAL_3333200091_02.pdf
document_url: https://eprints.untirta.ac.id/44128/12/MUHAMMAD%20FADHIL%20HILAL_3333200091_03.pdf
document_url: https://eprints.untirta.ac.id/44128/11/MUHAMMAD%20FADHIL%20HILAL_3333200091_04.pdf
document_url: https://eprints.untirta.ac.id/44128/6/MUHAMMAD%20FADHIL%20HILAL_3333200091_05.pdf
document_url: https://eprints.untirta.ac.id/44128/7/MUHAMMAD%20FADHIL%20HILAL_3333200091_06.pdf
document_url: https://eprints.untirta.ac.id/44128/8/MUHAMMAD%20FADHIL%20HILAL_3333200091_REF.pdf
document_url: https://eprints.untirta.ac.id/44128/9/MUHAMMAD%20FADHIL%20HILAL_3333200091_LAMP.pdf
document_url: https://eprints.untirta.ac.id/44128/15/MUHAMMAD%20FADHIL%20HILAL_3333200091_CP.pdf