Kusuma, Mohammad Angga (2024) PENGARUH VARIASI UKURAN MESH PARTIKEL BAMBU TERHADAP SIFAT MEKANIS DAN SIFAT FISIS PADA KOMPOSIT PAPAN PARTIKEL BERPENGUAT STEEL WOOL. S1 thesis, Fakultas Teknik Universitas Sultan Ageng Tirtayasa.
Text (SKRIPSI)
Mohammad Angga Kusuma_3331190035_Fultext.pdf Restricted to Registered users only Download (2MB) |
|
Text (SKRIPSI)
Mohammad Angga Kusuma_3331190035_01,.pdf Restricted to Registered users only Download (484kB) |
|
Text (SKRIPSI)
Mohammad Angga Kusuma_3331190035_02..pdf Restricted to Registered users only Download (238kB) |
|
Text (SKRIPSI)
Mohammad Angga Kusuma_3331190035_03..pdf Restricted to Registered users only Download (1MB) |
|
Text (SKRIPS)
Mohammad Angga Kusuma_3331190035_04.pdf Restricted to Registered users only Download (363kB) |
|
Text (SKRIPSI)
Mohammad Angga Kusuma_3331190035_05..pdf Restricted to Registered users only Download (59kB) |
|
Text (SKRIPSI)
Mohammad Angga Kusuma_3331190035_Ref..pdf Restricted to Registered users only Download (64kB) |
|
Text (SKRIPSI)
Mohammad Angga Kusuma_3331190035_Lamp..pdf Restricted to Registered users only Download (1MB) |
|
Text (SKRIPSI)
Mohammad Angga Kusuma_3331190035_CP.pdf Restricted to Registered users only Download (175kB) |
Abstract
Particle board is a board made from composite material made from pieces of wood and sawdust in the form of inorganic materials or can be in the form of organic materials. The use of wood to make particle board can be replaced with other materials. One mixture of materials for particle board is bamboo. Bamboo can be used for various purposes such as construction, furniture and so on. In this case, the size of the filler can affect the mechanical and physical properties produced by the particle board. This research aims to determine the effect of varying the size of bamboo filler on the mechanical and physical properties. In this study, variations in bamboo particle sizes were used with meshes of 35, 60 and 80. Meanwhile, for wood particle sizes, a mesh size of 35 was used. Where the percentage of material used was 30% bamboo particles, 30% wood particles, 29% PVaC, 1% SteelWool and 10% epoxy resin. Using the Cold Press Single Punch compaction method for 2 hours and through a post curing process at a temperature of 150 C for 1 hour. The resulting data shows that the best density, thickness expansion percentage, water absorption percentage and hardness are produced at mesh size 80. With the results of the density value, thickness expansion percentage, water absorption percentage and hardness, namely 0.76 gr/cm3, 1.24% , 50.78% and 50.67 Shore D. Meanwhile, the greatest bending strength was obtained at mesh size 35, namely 62.7 kgf/cm2. All particle board produced meets SNI 03-2105-2006 standards for its physical properties.
Item Type: | Thesis (S1) | |||||||||
---|---|---|---|---|---|---|---|---|---|---|
Contributors: |
|
|||||||||
Additional Information: | Papan partikel adalah suatu papan yang terbuat dari material komposit yang terbuat dari potongan-potongan kayu dan serbuk gergajian berupa bahan anorganik atau dapat berbentuk bahan organik. Penggunaan kayu sebagai pembuatan papan partikel dapat digantikan dengan bahan yang lain. Salah satu campuran dari bahan untuk papan partikel yaitu bambu. Bambu dapat digunakan dalam berbagai macam keperluan seperti dibidang konstruksi, meuble dan lain sebagainya. Dalam hal tersebut ukuran pengisi atau filler dapat berpengaruh pada sifat mekanik dan sifat fisis yang dihasilkan oleh papan partikel tersebut. Penelitian ini bertujuan untuk mengetahui pengaruh dari variasi ukuran filler bambu terhadap sifat mekanik dan sifat fisis. Dalam penelitian ini digunakan variasi ukuran partikel bambu dengan mesh 35, 60 dan 80. Sedangkan untuk ukuran partikel kayu digunakan ukuran mesh 35. Dimana digunakan persentase penggunaan bahan yaitu 30% partikel bambu, 30% partikel kayu, 29% PVaC, 1% SteelWool dan 10% resin epoksi. Dengan menggunakan metode kompaksi Cold Press Single Punch selama 2 jam dan melalui proses post curing pada suhu 150 C selama 1 jam. Data yang dihasilkan bahwa kerapatan, persentase pengembangan tebal, persentase daya serap air dan kekerasan terbaik dihasilkan pada ukuran mesh 80. Dengan hasil nilai kerapatan, persentase pengembangan tebal, persentase daya serap air dan kekerasan yaitu 0,76 gr/cm3, 1,24%, 50,78% dan 50,67 Shore D. Sedangkan, keteguhan lentur terbesar didapatkan pada ukuran mesh 35 yaitu 62,7 kgf/cm2. Semua papan partikel yang dihasilkan telah memenuhi standa SNI 03-2105-2006 untuk sifat fisisnya. | |||||||||
Subjects: | T Technology > TS Manufactures | |||||||||
Divisions: | 03-Fakultas Teknik 03-Fakultas Teknik > 21201-Jurusan Teknik Mesin |
|||||||||
Depositing User: | mr Mohammad Angga Kusuma | |||||||||
Date Deposited: | 06 Mar 2024 11:50 | |||||||||
Last Modified: | 06 Mar 2024 11:50 | |||||||||
URI: | http://eprints.untirta.ac.id/id/eprint/33911 |
Actions (login required)
View Item |