Rivaldi, Muhammad (2022) PENGARUH PENAMBAHAN UNSUR Al DAN MEDIA PENDINGIN CETAKAN TERHADAP SIFAT MEKANIK DAN STRUKTUR MIKRO PADUAN Cu-Al DENGAN METODE PERMANENT MOLD CASTING. S1 thesis, UNIVERSITAS SULTAN AGENG TIRTAYASA.

	Text (SKRIPSI) 3334170005.pdf Restricted to Registered users only Download (2MB)
	Text Muhammad Rivaldi_3334170005_01.pdf Restricted to Registered users only Download (333kB)
	Text Muhammad Rivaldi_3334170005_02.pdf Restricted to Registered users only Download (204kB)
	Text Muhammad Rivaldi_3334170005_03.pdf Restricted to Registered users only Download (574kB)
	Text Muhammad Rivaldi_3334170005_04.pdf Restricted to Registered users only Download (664kB)
	Text Muhammad Rivaldi_3334170005_05.pdf Restricted to Registered users only Download (315kB)
	Text Muhammad Rivaldi_3334170005_Ref.pdf Restricted to Registered users only Download (449kB)
	Text Muhammad Rivaldi_3334170005_Lamp.pdf Restricted to Registered users only Download (495kB)

Abstract

Copper and its alloys are commonly used as materials for electronic devices because of their properties, including electrical and thermal conductivity. The more copper is used, the more waste there is. Therefore waste copper must be recycled. Copper is commonly combined with other elements to improve its mechanical properties. One of them is aluminum to improve mechanical properties, including strength and hardness. Conventionally, Cu-Al alloys are usually produced by casting, one of which is for the manufacture of propellers. However, if using conventional casting such as the sand casting method, there are still many defects in the casting results. So in this study, the permanent mold casting method was chosen. Copper waste is casted by adding variations in weight percent of Aluminum so that it becomes a Cu-Al Alloy using the permanent mold casting method which is varied with the cooling media of the mold. The addition of Aluminum aims to improve the mechanical properties of copper with various additions in weight percent of 1%, 3% and 5%. While the variation of mold cooling media aims to determine the effect of cooling on the rate of freezing of castings, mechanical properties and microstructure with variations of the cooling media used in the form of air, wet sand and water. All casted at a temperature of 12000C until melted and then poured into a mold that has been given a cooling medium for the mold to freeze. Analysis of mechanical properties was carried out by testing the hardness using the Hardness Vickers method and testing the wear (wear test) using the ogoshi method. Microstructure analysis using optical microscope and ImageJ application. After the research was conducted, it was found that the addition of aluminum can improve the mechanical properties of copper, namely hardness and wear. The cooling medium of the mold also improves the mechanical properties of copper and affects the microstructure, which is to restrain grain growth so that the grain size becomes smaller. The best hardness results are 214,047 HV, the best abrasion specification value is 3,031908 x 10-6 mm3/mm and the best grain size is 29,787 μm with the addition of 5% Aluminum and the use of water mold cooling media.

Item Type:	Thesis (S1)
Contributors:	Contribution Contributors NIP/NIM Thesis advisor SURYANA, - 197402162001121001
Additional Information:	Tembaga dan paduannya biasa digunakan sebagai material untuk perangkat elektronik karena sifatnya, termasuk konduktivitas listrik dan thermal. Semakin banyak penggunaan tembaga, maka semakin banyak pula limbahnya. Oleh karena itu limbah tembaga harus didaur ulang. Tembaga biasa dipadukan dengan elemen lain untuk meningkatkan sifat mekaniknya. Salah satunya adalah aluminium untuk meningkatkan sifat mekanik, diantaranya kekuatan dan kekerasan. Secara konvensional, paduan Cu-Al biasa diproduksi dengan pengecoran, salah satunya untuk pembuatan propeller. Bagaimanapun, jika menggunakan pengecoran konvensional seperti metode sand casting, masih banyak cacat pada hasil pengecoran. Maka dalam penelitian ini dipilih metode permanent mold casting. Limbah tembaga dicor dengan menambahkan variasi persen berat Aluminium sehingga menjadi Paduan Cu-Al menggunakan metode permanent mold casting yang divariasikan dengan media pendingin cetakan. Penambahan Aluminium bertujuan untuk meningkatkan sifat mekanik dari tembaga dengan variasi penambahan dalam persen berat sebesar 1%, 3% dan 5%. Sedangkan variasi media pendingin cetakan bertujuan untuk mengetahui pengaruh pendinginan terhadap laju pembekuan coran, sifat mekanik serta struktur mikronya dengan variasi media pendingin cetakan yang digunakan berupa udara, pasir basah dan air. Semua dicor pada temperatur 12000C hingga melebur lalu dituangkan ke dalam cetakan yang telah diberi media pendingin cetakan hingga membeku. Analisa sifat mekanik dilakukan dengan pengujian kekerasan menggunakan metode Hardness Vickers dan pengujian keausan (wear test) dengan metode ogoshi. Analisa struktur mikro menggunakan alat mikroskop optik dan aplikasi ImageJ. Setelah penelitian dilakukan, didapatkan hasil bahwa penambahan aluminium dapat meningkatkan sifat mekanik dari tembaga, yakni kekerasan dan keausan. Media pendingin cetakan juga meningkatkan sifat mekanik tembaga serta berpengaruh pada struktur mikro yakni menahan pertumbuhan butir sehingga ukuran butir menjadi lebih kecil. Didapatkan hasil kekerasan terbaik sebesar 214,047 HV, nilai spesifikasi abrasi terbaik sebesar 3,031908 x 10-6 mm3/mm dan ukuran butir terbaik sebesar 29,787 μm pada penambahan 5% Aluminium dan penggunaan media pendingin cetakan air.
Subjects:	T Technology > T Technology (General) T Technology > TS Manufactures
Divisions:	03-Fakultas Teknik 03-Fakultas Teknik > 27201-Jurusan Teknik Metalurgi
Depositing User:	S.T. Muhammad Rivaldi
Date Deposited:	15 Feb 2023 08:52
Last Modified:	15 Feb 2023 08:52
URI:	http://eprints.untirta.ac.id/id/eprint/16450

Actions (login required)

View Item